Jun. 09, 2025
Conveyor belt specialist Jeremy Clark shares his essential dos and don’ts when buying industrial conveyor belts.
Please visit our website for more information on this topic.
Conveyors are indispensable but expensive pieces of equipment. With operating budgets under continuous scrutiny from senior management, it is all too easy to make a costly mistake when buying conveyor belts. Here, conveyor belt specialist Jeremy Clark shares what he considers to be the most important dos and don’ts when buying industrial conveyor belts.
Never assume that the specifications of your conveyor belts are correct. Most conveyors have been in operation for a number of years. During their lifetime they are likely to have been operated by several different managers and maintenance personnel. It never fails to surprise me to find that mistakes have been made by the original builders of the conveyor when calculating the belt specification best suited to the conveyor. Likewise, subsequent attempts to solve problems such as rapid wear and ripping and tearing, may have resulted in the wrong specification of belt being fitted. The same applies if the material mix or volumes have changed significantly. It is imperative that the belt specification always matches the conveyor design and the materials being conveyed.
For example, belts that are too thick for the design of the application can cause problems such as excessive rigidity (lack of troughability) and steering and handling difficulties. The same applies to tensile strengths that are too high. It is important to remember that for every step increase in tensile strength, the pulley and drum diameters need to be increased by 25%. The belt carcass may fail due to dynamic stress if this action is not taken. Quality belt manufacturers and their service partners who supply and fit their belts, will have experienced engineers. When provided with sufficient information, they can verify the belt selection.
Always select belts based on their durability, suitability and longevity (whole life cost) rather than for short-term ‘economic’ or budgetary motives. Experience shows, without doubt, that the price of the belt will invariably be reflected in both its quality of performance and the length of its working life. I regularly see cases where a good quality belt can produce a working life of more than five years compared to low-grade belts that have been purchased on the basis of their low price but need regular repairs and then have to be replaced after only a year or two, often less.
The biggest source of low-price, low-grade belting is, of course, the Far East, primarily China. Their prices may be very tempting, but it is important to understand how those prices are achieved. The ‘lower labour costs’ argument is a fallacy because the labour element accounts for as little as 5% of the production cost. The true reason for the difference in price is that raw materials make up to 70% of the cost of producing a conveyor belt. Consequently, the only way to manufacture a low-price belt is to use low-price (low grade), unregulated raw materials. There simply is no other way. Cost-cutting practices include using cheap, low-grade carbon black made by burning old car tyres, the use of ‘bulking fillers’ such as clay instead of good quality polymers and using low-grade inner synthetic plies. The two best indicators of poor quality rubber are its low price and its pungent smell. Good quality rubber rarely has any smell at all. As the old saying goes, price is what you pay but cost is what you spend.
Always (unless significant quantities are involved), choose belts from within the manufacturers standard stock range whenever possible Any deviation from the standard specification of a belt held in stock means that the belt would have to be made to special order, invoking higher production costs and potential minimum length order quantities. It also increases the delivery lead time, which can be especially bad newsif a belt needs to be replaced inan emergency.
Only buy belts when you are totally confident of their provenance (manufacturer’s origin) and where the manufacturer clearly states the level of anticipated performance rather than simply claiming to have been tested to a certain standard. Unfortunately, in today’s market, with the exception of Fenner Dunlop in The Netherlands and North America, nearly all manufacturers now supplement their production with imported belting, mostly from the Far East. My advice is to always ask for certified confirmation of the actual place of manufacture.
Avoid over-specifying the type of belt edge. This may surprise you, but it can have a very significant impact on belt costs, repairs, maintenance, lost production and lead times. Many years ago, moulded edges (fully covered in rubber) were the standard because cotton was used as the reinforcing fabric in multi-ply belts. A moulded edge was therefore essential to prevent moisture penetrating the cotton fabric and causing it to rot. Since the introduction of synthetic ply fabrics using polyester and polyamide, this problem effectively no longer exists. Despite this, many conveyor operators and their buying departments continue to specify moulded edges, even though they do not provide any structural or performance advantage and can actually be susceptible to damage if the belt wanders off-track.
Nowadays, the most commonly used type of belt edge is the ‘cut & sealed edge’ or simply ‘sealed edge’, which is sufficient to prevent moisture being drawn into the carcass from the edge by capillary forces. Although the synthetic fibre plies are barely affected, moisture can ultimately cause vulcanising problems when making splice joints. A sealed edge also enables a belt to be used in very wet conditions and makes it better suited to long-term storage outdoors.
The reason why it is important not to over-specify the type of belt edge is that manufacturers need to manufacture belts at the optimum width and length for cost and production efficiency. Consequently, standard width stock belts are usually made as wide as the manufacturing machinery will allow, creating huge rolls known as ‘slabs’. These are then cut and sealed to create a range of narrower widths. For example, using metric measurements in this case, 400 meters of 2,200mm wide belt ‘slab’ would be manufactured and then be slit (cut) to produce 400m of 1,000mm wide belt and 400m of 1,200mm wide. This is why the vast majority of rubber multi-ply belting held in stock by manufacturers, distributors and traders has sealed edges. Moulded edges can only be created when a belt is manufactured in isolation and to an exact width. Consequently, the manufacturer is unable to achieve optimum production line efficiency, the cost of which has to be reflected in the selling price.
Never order a conveyor belt without first obtaining written confirmation from the supplier/manufacturer that the belt being supplied is fully resistant to ozone and UV. As every manufacturer of rubber products will know only too well, at high altitude ozone (O3) acts as a protective shield by absorbing harmful ultraviolet rays but at low altitude, it becomes a pollutant that attacks the molecular structure of rubber. Ground level ozone increases the acidity of carbon black surfaces with natural rubber, polybutadiene, styrene-butadiene rubber and nitrile rubber being the most sensitive to degradation. The reaction that occurs is known as ozonolysis.
The first visible sign is when cracks start to appear in the surface of the rubber. Further attacks then occur inside the freshly exposed cracks, which continue to grow steadily until they complete a ‘circuit’ and the product separates or fails.
Ultraviolet light from sunlight and fluorescent lighting also has a seriously detrimental effect on rubber because it accelerates rubber deterioration by producing photochemical reactions that promote the oxidation of the rubber surface resulting in a loss in mechanical strength and wear resistance. This is known as ‘UV degradation’. The combination of ozone and UV has a seriously limiting effect on the operational lifetime of a rubber belt, regardless of geography or type of climate.
Fortunately, ozone and ultraviolet damage is easy to prevent. Unfortunately, laboratory testing consistently reveals that some 90% of belts tested according to EN ISO /1 procedure B static ozone resistance test are not resistant. In fact, the vast majority typically start to crack within the first 6 to 8 hours of the 96-hour test duration. This is because the anti-ozonants needed to protect the rubber have been omitted from the rubber compound mix because of cost so always insist on ozone & UV resistance when selecting any rubber conveyor belt.
Choose belts that are specifically engineered for the conditions they are required to cope with. This is especially important on sites where rip, tear and impact damage problems occur. Attempting to solve the problem by fitting belts with thicker covers and heavier carcasses is invariably a mistake. Simply using more of the same material will not provide the solution. As mentioned earlier, thicker, heavier belts can also cause other problems including lack of troughability, steering and handling problems and dynamic stress due to the pulleys and drums now being
too small.
The most economical solution is to fit a conveyor belt that has been specially designed for the purpose, such as Fenner Dunlop’s UsFlex, Nova X and Ultra X range belts that are proven to last up to four or five times longer than conventional multi-ply conveyor belts. The initial buying price might be appreciably higher, but the cost will be substantially less over the working life of the belt, with the added benefits of far less repairs, change-out costs and disruption to output.
Always choose a belt supplier who you can rely on to be accountable in the event of a problem. It is important to have a supplier that will readily provide a high standard of professional technical support and who has a good reputation for quality. This, I feel, should always be an essential part of the criteria when choosing a supplier. A tall order perhaps, but they do exist.
Well-Made Essentials »
No accessory is as frequently overlooked as the belt. Denimheads generally opt for untucked looks, so the belt is often hidden away. Since it’s so rarely noticed, many untucked denimheads simply transfer their trusty old belt into their raw denim. Job done.
Some don’t even go this far. In both untucked looks and tucked ones, it’s surprisingly common to see top-shelf denim with empty belt loops. It’s like boots without socks or coffee without caffeine: something’s wrong; something’s missing.
Most of us don’t need a belt to hold our pants up. If we’ve found the perfect-fitting pair of jeans, they sit exactly where they should sit with or without a belt. But this isn’t why we cinch the strap of leather around our waist.
We wear a belt primarily to frame our jeans. Each side of the frame should match. If we’ve gone with boots below the cuff, we need matching leather at the waist. We need to complete the frame. The picture is incomplete without it.
If you’re still using your old belt, or if (gasp) you’re not wearing a belt at all, the list below will be an excellent starting point.
Back to guide overview
Mass-market retailers almost always have a rack of belts somewhere in the shop. Give them a miss. These chrome-tanned belts can’t hold a candle to the genuine veg-tanned article.
If you want a belt worthy of your top-shelf selvedge, start at the door of your local well-made goods stockist. Better yet, use the list below to help you narrow down your search from the comfort of home.
NB: This list focuses on natural belts that patina with age, but all of these makers offer belts in a wide range of colours. We prefer natural belts for the patina potential, but you might prefer to start with a dyed belt. Even if it’s been dyed, if you start with the right maker, you’ll get a great belt that will get better with age.
We’re leading off with a strong contender for the denim world’s favourite belt maker. Isaac is a self-taught craftsman with as strong a passion for well-made goods as you’ll ever encounter. If you’ve spent any time poring over pictures of faded denim (and who hasn’t?), you’ve probably seen dozens or even hundreds of pictures of his belts.
Speaking from experience, the quick-release buckle (a 19th-century design that gave firemen quick access to their bundled hoses) takes a few days to get used to. As its name suggests, it releases very quickly, but putting it back together takes a bit of practice.
After a couple of days of bathroom breaks, you’ll be operating it like a master. Both belt and buckle will patina beautifully.
Other PigeonTree belts to consider: There’s not a belt in Isaac’s range that will disappoint. We’re particularly fond of the Navy Sedgewick (a rich and vibrant dark blue), Horween Chromexcel (the truly classic leather), and for the man who has everything, the Green Tärnsjö (complete with sterling silver buckle).
PigeonTree Crafting ship from the US. The only place to buy Isaac’s belts is directly from the maker himself.
The pride of Singapore, Obbi Good Label continues year after year to prove that they belong in any conversation about the world’s best makers of dependable leather goods.
Their bags and wallets are a popular favourite in the denim community, and, thanks to their immediately recognizable octagonal buckle, their belts have become something of a standard for picky denimheads.
They make these belts out of full-grain South American bovine leather held together with a single brass screw post. They promise that the belt is ready for lifetime use, and we’ve yet to see anybody wear through one of these things. It’s a belt for the ages, and it’ll quickly show onlookers that you take both denim and leather seriously.
Other OGL belts to consider: Single Prong Natural (same belt but with only one prong), Vintage Natural (same leather, but a more classically styled buckle), Narrow Natural (thinner with a more elegant buckle)
Iron Heart ship from the US and the UK. If you’re looking for other places to buy OGL belts, try: Standard & Strange (USA), Franklin & Poe (USA), James Dant (USA), Rivet & Hide (UK), Second Sunrise (Sweden), Untouched (Australia)
Studio D’Artisan are better known for their impeccable work with denim than with leather, but the brand was one of the original badges behind the raw denim revolution, so, when they speak, the denim world listens. They do simple things as well as anybody, and this belt is no exception.
Even just a glance at the made-in-Japan veg-tan beast shows you that this belt means business. It’ll put up a fight for a long while, but, when it stops fighting, you’ll have a friend for life.
It may not be as thick as some of the heavyweights on this list, but it’s made out of bend cowhide, one of the world’s toughest forms of leather, so it more than makes up in heart what it gives away in bulk. It comes with a matching leather keychain, so you can race the two to see which will cross that perfect patina line first.
Other SDA belts to consider: The Bend Cowhide belt is also available in Brown and Black.
Corlection ship from Australia. If you’re looking for other places to buy SDA belts, try: Okayama Denim (Japan), Son of Stag (US), DC4 (Germany), Self Edge (USA), Blue Owl (USA), Frans Boone (Netherlands)
There’s significant competition in this space among the major Japanese denim brands. You really can’t go wrong with any of them.
Momotaro, UES, and Strike Gold (just to name a few) all make excellent veg-tan belts that would be perfectly at home on this list. With so many great makers to pick from, making these choices has not been easy.
Along with Iron Heart, Stevenson, and SDA, who also made this list, Samurai just pushes their craft that little bit further. They make everything with the future in mind. Their denim is some of the best fade foundations around, and their small range of belts will make an excellent companion for your fade journey (no no matter how long the road stretches ahead of you).
Their Full Grain Garrison Belt has a sheen that makes it stand apart from a lot of the other belts in this space. It’ll quickly begin to change colour, and the inner character of the leather will come charging to the surface. The hand-stitched details mark this as a quality piece. Like the leather, this stitching will change colour as the belt ages.
The Samurai Full Grain Garrison Belt is also available in Brown and Black. They also have a Heavy Curved Belt made of 5-8mm American Steer hide in the same colour range.
Corlection ship from Australia. If you’re looking for other places to buy Samurai belts, try: Okayama Denim (Japan), DC4 (Germany), Son of a Stag (USA), and Statement (Germany)
If you want bulletproof accessories to go with your tough-as-nails selvedge, Iron Heart has got you covered.
The brand has built their reputation on the durability and dependability of their products, and it’s no surprise that they make a prominent appearance on a number of our Well-Made Essentials lists. They’re leaders in nearly every category—not just denim, but anything that pairs well with denim.
Their Heavy Duty Tochigi Belt is another square-buckle made-in-Japan beauty. It’s 4.2mm thick, so it’s not the heaviest piece on this list, but it’s anything but a lightweight. They’ve chosen a brass Chicago screw assembly, which allows you to adjust the belt’s length for a perfect fit. Like the other garrison belts on this list, there’s no keeper, so it’s best to keep that in mind when sizing.
The Tochigi Garrison Belt is also available in Brown and Black. It’s also available with a Brass Garrison Buckle and in a more Classic Buckle style.
Iron Heart ship from the US and the UK. If you’re looking for other places to buy Iron Heart, try: Franklin & Poe (USA), Corlection (AUS), Self Edge (US), Franklin & Poe (US), Brund (Denmark), and Statement (Germany)
Our last natural veg-tan belt is from another of our favourite American leather artisans. There’s a great deal to be said for the Japanese brands operating in this space, but they’re leveraging their reputations as excellent denim makers for a leap into the leather goods space.
PigeonTree, Guarded Goods, and Tanner Goods have all built their reputations entirely on their leatherwork. In a space as crowded as this one, distinguishing yourself doesn’t come easy, so these reputations are meaningful.
The kind of care and quality you can expect from Portland-based Tanner Goods is on full display with their Standard Natural Belt. Made of a hefty 11 oz. veg-tan leather, the belt has heft to spare, and there’s a rich creaminess in both look and feel that has made this belt a huge hit with finicky denim fanatics.
If you’ve made it this far and still haven’t found what you’re looking for, this beauty might punch your ticket.
You will get efficient and thoughtful service from BEIOUTE.
Tanner’s standard belt also comes in Cognac/Copper and Mahogany/Black combinations. They have a wider range of thicknesses and buckle combinations on their website.
Stag Provisions ship from the US. If you’re looking for other places to buy Tanner Goods belts, try: Division Road (USA), Tanner Goods (USA & Europe), Two Jacks Denim (USA), and Bridge and Burn (USA)
We’re huge fans of self-ageing everything, but a piece occasionally comes along that makes us consider breaking our rules. The Stevenson Narrow Cowhide Belt is one of them.
Stevenson started its life as an American brand, but it didn’t last very long. Japanese style wizard Atsuke Tagaya restarted the defunct brand in , and, ever since, their timeless jeans, jackets, and shirts have been making themselves right at home in deep rotations.
They’re not the first brand that denimheads reach for, but they are absolutely perfectly at home in any conversation about the best Japanese brands in the denim game.
Because it is much narrower than the other belts on this list, their Narrow Cowhide Belt tips into decidedly western territory. It looks phenomenal with higher-rise jeans or, even better, with chinos. The 4mm Japanese cowhide is more than tough enough to last, and the snap-on construction makes for easy adjustment or replacement (it’s unlikely this will be necessary).
If you want a multi-use belt that comes out of the box looking like a finely aged masterpiece, look no further.
Stevenson Overall Company also offers a version of their belt with studs and conchos. Their Narrow Cowhide Belt is also available in Black, and they also have a regular width version in both colours.
Corlection ship from Australia. If you’re looking for other places to buy Stevenson Overall Company belts, try: Son of a Stag (USA), Rivet & Hide (UK), Cultizm (Germany), and Burg & Schild (Germany).
We’re closing this list with a piece that’s bound to stir up some controversy. It’s a more dramatic statement than anything we’ve covered above. If the idea of a straightforward buckle bores you to tears, American belt makers Colonel Littleton have a few tricks tucked through their belt loops.
The Colonel (an honorary title) says that he is in the “wanting” business, not the “needing” one. They make leather products with discerning customers in mind, and the popularity of the brand’s bags and belts are a testament to the Colonel’s ability to give his customers exactly what they want (even if it’s a little more than they need).
The #5 Cinch Belt is their most iconic and immediately recognisable piece. Rather than adjusting the belt at the front, you adjust it at the side. Once you’ve hitched the two pieces together with the clasp that sits on the hip, the cinch buckle at the front opens and closes easily.
The look is not for everybody, but those who want their belts to stand apart from the crowd wouldn’t dream of wearing anything else.
Other Colonel Littleton belts to consider: The No. 5 Cinch Belt is also available in Italian Bridle Leather (a little cheaper as well). There’s also the No. 1 Surcingle Belt (more classic belt, but still with the hip adjustor) and the No. 4 Leather Belt (a black western classic).
Colonel Littleton products are exclusively available through their webshop.
For some of Guarded Goods’ more devoted fans, these belts should have headlined this list. Undeniably one of the best leather workers in the United States, Guarded Goods uses American leather in all of their products (finishing it with American-made hardware).
Every one of their items is hand-made by the passionate maker at the heart of the brand.
The principle he abides by is one that denimheads will recognize: buy a little bit less but spend a little bit more for something that is made purposefully and passionately.
His Foundation Belt is available in several leathers and colours, and with an equally wide range of buckle and closure options.
We’re particularly fond of the belt pictured below: a Hermann Oak Natural Veg Tan with the antique brass square garrison buckle. Rivets are always a durable choice, but you can upgrade to a closure carefully stitched with waxed thread that gives the belt a decidedly hand-made feel. Whichever options you choose, this belt will be with you for life.
Thanks to its fully customisable leather and buckle options, it’s one-stop shopping for belts with Guarded Goods. We can recommend the incredible stiff English Bridle Leather in London Tan, Natural Russet, or Black.
Guarded Goods ship from the US. Their belts, wallets, and other leather goods are exclusively available through their webshop.
Denimhunters is reader-supported. If you buy after clicking a link on our site, we may earn a commission.
First as functional pieces and later as fashionable ones, belts have been with us for almost all of human history, and there’s no chance of them going the way of the dinosaur. If we want to be taken seriously, we need a good belt (ideally one that matches our footwear).
The precise origins of belts are difficult to buckle up, but we do know that belts predate pants. They’ve been with us since the bronze age, starting as ways to secure tunics and as places for soldiers to store weapons and other supplies they might need on the charge or on the run.
On the battlefield, a man’s belt was absolutely essential. It was not only for storage, it was also (when made of sturdy animal hides or metal) a protective covering for some of the body’s more vital bits. This made it a suitable (and bloodless) trophy that the victor could carry off the battlefield. This practice echoes down to us through the ages—the winners of boxing or martial arts bouts still leave the ring carrying with a shiny belt slung over their shoulder.
There’s a long history of finely decorated belts, which were common signs of wealth and prestige both on and off the battlefield for centuries. We’re more interested, though, in the belt as a purely utilitarian accessory.
This means we’re looking at the early part of the twentieth century, with as perhaps the most important year in the belt’s workwear history. This was the first year that Levi’s started to include belt loops on their jeans. Their earlier models featured cinch backs and suspender buttons, but no belt loops.
The loops appeared at the same time that the waistband and the navel started to part ways. Jeans were still by every measure what we’d call a high-rise jean today, but the waist was starting to retreat. Jeans were now worn across the hips rather than above them, and this made the belt increasingly essential.
Over the next few decades, the belt started to tighten its grip on the denim world. When we look at pictures of style icons from the ‘50s and the ‘60s, we see more and more of them feeding belts through those loops. The back cinch and suspender buttons almost entirely disappeared. In the evolutionary battle for supremacy, the belt had come out on top.
Depending on how diverse your tastes, you might be able to get away with a single well-made belt. If you’re suiting up each morning in heavy denim and brown or black boots, you might be able to make do with a single heavily patinated belt—one belt to rule them all. One belt to bring them all and, in the darkness bind them.
This is what most denimheads do. They find a belt that works with their go-to style of denim and footwear and they just move that belt between pairs. It works with everything, so why mess with perfection.
If all your boots are black or brown, a well-made belt in the same colour will always work. If, however, you have a wide-ranging boot collection, you probably already have at least a couple of belts. If you’ve made do with a single black or brown belt while your boot collection has grown, it might be time to start branching out.
For medium rise or lower rise jeans, a wide belt (at least 1.5 inches) tends to look the best. As the jeans rise to the top of the hips, slightly thinner belts become more appropriate, but denim generally demands that you err on the wider side.
Dress belts, often with a fair bit of shine to them and usually close to a single inch in width, tend to work best with softer fabrics. They’re perfect with chinos and dress slacks, but they create a somewhat lopsided picture when paired with heavy denim and boots.
Of course, the opposite can be true if you prefer slip-ons or oxfords below the cuff. A dress belt in the right shade will work exceptionally well with slip-ons or loafers. Be warned, though: heavy denims and dress shoes/dress belts make uneasy bedfellows. Copacetic pairings tend to feature three pieces pulled from the same weight class. Heavy belt? Heavy denim and boots. Dress belt? Chinos and loafers.
Most of the belts below will work better with boots than with dressier looks. A few of them will slide nicely into chinos or other softer looks, but only accidentally. This is a website for denimheads, so we’re assuming that you’re looking for a well-made belt that will slide perfectly into your rotation of well-made selvedge (and probably boots too).
Back to guide overview
A lot of the well-known brands in this space either produce excellent belts of their own or collaborate with top-notch belt makers. It seems a natural fit, and every stockist will have an assortment of belts to pair with the jeans they sell.
We’re spoiled for choice, and the number of brands in this space can be dizzying, so we’re going to help you narrow down your search. Here’s what to look for.
As with boots, 100% leather simply won’t cut the mustard. We need more than that.
Those who make the best belts take extra care to start with the best available leathers. You should be able to see this immediately. You should expect full-grain leather. Look for subtle variations in colour on the surface of the belt. Does it look like plastic, or does it look like an animal’s skin (imperfections and all)? Only the latter will do.
You might have heard words like ‘veg-tan’ or ‘vegetable-tanned’ floating around in discussions about belts. In this context, vegetable doesn’t refer to carrots or broccoli. Rather, it refers to the all-natural tanning process, a much slower and environmentally friendly tanning process that, with the help of the tannins in oak and spruce bark, produces a supple but durable leather.
Best of all, the leather remains porous enough to allow oils to penetrate its surface. This means that, unlike chrome-tanned leather, vegetable-tanned leather will patina with age. This is why denimheads can’t get enough of the stuff.
You’ll notice that quite a few of the makers on this list offer natural or raw leather options. Like raw denim, this belt is purchased in an unfinished state. While fading denim is the art of subtraction, with a raw veg-tanned belt, we are practising the art of addition. The oil from our skin transfers to the belt and it takes on the beautiful brown tones that no amount of dye can replicate.
If you’ve never been through this process, we highly recommend it. Yes, the belt clashes with everything for a few months, but, as with raw denim, our patience is rewarded. We end up with a belt that is uniquely our own, shaped by how we’ve worn it and handled it.
What to look for in a well-made leather belt:
How it’s made really comes down to two things. The stitch and/or rivet work and the hardware. With most of the belts we’ll cover below, the stitching is confined to the area around the buckle assembly. The rest of the belt showcases the high-quality leather.
The belt maker folds one end of the belt over to create a loop that the buckle will sit in. The end is then fastened to the rest of the belt either with heavy-duty stitching or sturdy rivets. The buckle is usually a fairly simple affair, though some makers (PigeonTree and Colonel Littleton spring to mind) feature thoroughly original patented buckles that make their belts immediately recognizable.
There’s no need to go with an extremely heavy buckle. There are plenty of extremely well-made belts that aren’t topped off with industrial-grade materials.
This is one of those categories in which even some of the best makers seem determined to outdo everybody else in the field by producing the biggest and baddest hardware around. This hits a lot of denimheads right in the sweet spot, but it’s often more than is absolutely necessary.
If nothing but the toughest piece of leather held together by Vulcan-forged steel will do, by all means, reach for that heavyweight champion. If you’re simply looking for a high-quality belt, though, there are plenty of middle-weights that will keep your pants up and look great while doing it.
Construction details to look for in a well-made leather belt:
Our favourite belts are all made to take on character as they age and share experiences with the wearer. The oils from our hands will turn it a rich golden brown, and it’ll just keep getting darker and darker through the years.
We’ll add a little blue into the mix each time we wear the belt to break in a new pair of raw denim, and we’ll end up with a belt that we’ve had a hand in producing.
Great makers all offer their customers the opportunity to patina their belts like this. They’ll offer dyed versions of the belts as well, but the diehard patina enthusiasts are as likely to buy these (as beautiful as they are) as denimheads are to buy pre-faded denim.
If you’re evaluating a maker that’s not on this list, see if they offer raw versions of their belts. It’s a surefire sign that the maker speaks your language.
If you’ve got the belt, you definitely need the jeans and the boots to pair it with. If you’ve got the downstairs covered, it might be a good time to start looking at a jacket or a heavy-duty flannel. The right belt will tie the whole outfit together perfectly.
Contact us to discuss your requirements of Raw Edge Belt(uz,es,it). Our experienced sales team can help you identify the options that best suit your needs.
Previous: Is SPC Click Flooring the Ultimate Solution for Durable and Stylish Living?
Next: 2023 SPC Rigid Core Flooring Prices: What to Expect and Compare
If you are interested in sending in a Guest Blogger Submission,welcome to write for us!
All Comments ( 0 )