Key Questions to Ask When Ordering dust seal

I’ve added dust collectors to my shop both because it’s necessary for some equipment, like my planer and jointer to operate and because I wanted to reduce dust and chips in the shop.

Goto Langnuo Mining Equipment to know more.

A majority of collectors for small shops can be greatly improved. For example, one of my smaller collectors came with a thirty micron bag. Many others only go down to five or ten microns and a lot of those only after the bags used for filtration start to clog.

Since dust particles can be much smaller than these systems stop, they have earned the name “Dust Pumps.” After several years of using collectors, I think this is an appropriate name for many of them.

Add to the foregoing the fact collection bags and filters used for these systems don’t always seal well to the metal body of the collectors, so some fine dust escapes at those points too. The second picture shows dust trails from where dust was escaping from under my collection and filter bags.

With just a little research on the matter of woodworking dust, it become immediately apparent chips and such are a nuisance, but dust small enough to be carried in the air and get in your lungs is a very real danger.

Clearly, everything you can do to improve dust and chip collection in your shop is a good thing. To that end, I tried using duct tape. It helped, but only if the surfaces were clean before application. Then there is the matter of trying to get duct tape to seal a cloth bag to a metal surface. Over time, the tape fails, where it attaches to the cloth, and you need to apply more. After a while, it can get pretty ridiculous and unsightly.

To solve that problem, I merely purchased some foam gasket material used for sealing campers to pickups. It’s varies in thickness and width. The role I bought was about 5/16" thick by 1-1/4" wide by 30’ long and ran about seven dollars, even on Amazon Prime.

Unfortunately, I was preoccupied with solving a problem and did not think to document the improvements with photos. However, a simple description should make it easy for anyone desiring to improve the seal on their system to make this simple modification.

The foam I purchases can be seen in the photos. It was from M-D Building Products and was indicated to be product item “ Camper Seal Tape.” It has a self adhesive side, so not tools, other than a sharp blade or scissors were required for installation.

To install it, you must, of course, remove the upper and lower bag(s) from the collector.

Once the bags are removed, merely wipe down the surfaces to remove all dust or anything else that might interfere with adhesion.

Start applying the foam sealer where each bag will be installed and sealed. Do not pull so tightly you stretch the foam, since this will cause it to want to pull against the adhesive and shrink back to its original length.

When you get to the place where the two ends will meet, cut it long enough so the two will push against each other. Merely laying the end over the start will give you a good idea of where to cut.

If you do get a gap, consider cutting about an inch off the applied gasket and filling that gap with a new pieces.

Now, just install the bags and your system should be ready to get back to work.

NOTES:

• I suggest switching cloth bags to plastic ones. Many of us just just clear plastic lawn bags and dispose of them when full. Though they are lightweight, they seem to work well and a box of several of them runs about the price of a couple of the heavier bags.

Even when I used heavier bags, they developed holes during removal. This happened even more often with my smaller collector, which used a flexible ring to hold the bag in place, than it did on my larger collector, which used a band and lever.

• At the first opportunity, order finer micron bags, or the more expensive canister filters. They do a much better job of filtering the air than do most stock bags. Go down to at least one micron and a half is even better.

• Consider a cyclone pre-filter. Ones like the Super Dust Deputy REALLY work and remove all the chips and most the dust before it ever gets to the bag filter. One more advantage of this is, object that, otherwise, would go through your collector impellers are spun out by the cyclone, prolonging your impeller life, and giving that pair of safety glasses a chance of survival, since they don’t get drawn through moving parts.

"":http://

If you’re not familiar with how to calculate dust collection CFM, the process can be intimidating. Visit our article here where we will help you understand our approach to calculating CFM requirements for you. Along with the questions you should be asking your dust collection engineering firm to identify the optimal solution for your plant.

The best method of dust removal from your hopper is dependent on multiple components. Learn Is your dust low in density like wood chips or is it higher in density like fine steel dust? Check out this video to learn more about bulk density and other dust properties. more about dust removal options in this article linked here.

Can velocity is the speed at which air moves from low in the baghouse to high. The higher the can velocity, the faster air moves up in the system. The right can velocity for your dust collection system will be based upon your application and the density of your product. At US Air Filtration our engineers calculate your can velocity based on a few different factors. Visit our can velocity article to get an introduction to dust collection can velocity, it’s importance and impact on system performance, solutions to excessively high can velocity, and how you can calculate yours in 3 easy steps.

Air to cloth ratio in your dust collection system is a critical measurement to keep your system running at peak efficiency. In this article (video option included), learn why it’s crucial to dust collector performance, how to calculate it, and the negative impacts of improper air to cloth ratio.

Air temperature at the inlet duct is just one of the factors that help our equipment specialist identify the right system for you which will perform safely, efficiently, and reliably for many years. If you would like to learn more about the factors to consider for a new dust collection project, visit our dust collector purchasing guide here.

Are your dust characteristics explosive? Linked here are the conditions needed for an explosion and the most common industries that work with combustible dust.

There are multiple strategies for dust collection explosion venting. The best method for your facility will depend on a variety of factors. Learn more about these factors, the best explosion venting strategies, and also prevention methods available in our article here.

“What’s the best way to collect the dust at that dust creation point?” Three common methods are: Tap, Hood, Articulating Arm

Many facilities include source taps at every machine. If there are no taps, then a hood or a smaller pickup point can be added. For example, a hood can be added above a table to capture dust if there is a need to constantly maneuver around the table.

If you require a fan, check out this resource we have on dust collector fans that will and learn how you can size your dust collector fan with this easy 5-step process. Includes a video and access to a free project consultation with an equipment engineer.

The right dust removal method for your dust collector can help you avoid air flow being blocked off, loss of suction throughout the system, and a dangerous explosion that can happen due to dust build-up in the hopper. Learn the factors that go into choosing the right dust removal method and what they are here.

Dust collectors vary in height, width and depth depending on the application and the amount of dust being captured. Take note of any height or space restrictions in the work environment and take measurements of the space allotted for your collector along with the space available around the collector. Many dust collectors are top load which means you will need to allow space above the collector to replace and service the collector from the top of the unit. To learn more about identifying the right solution for your application, visit our complete Dust Collector Purchasing Guide here.

Choosing the right filter bags for your dust collection system is critical to ensuring long term, reliable performance of your collector and the safety of your employees. Our How to Select the Right Dust Collector Filter Bags” guide will help you understand your facility’s unique dust properties and also provides an overview of various filter media, construction, and treatment options available

A well maintained dust collector ensures your system is performing at peak efficiency. It’s also critical to minimizing unscheduled plant downtime and the wear and tear of your dust collector parts. In addition to a preventative maintenance plan, customers can also request a visit from bonded and insured technicians to perform either a dust collector inspection or service. Below is a list of questions we typically ask in order to provide a quote. For more information about dust collector inspection and services, visit this article where we help you understand what’s included and the differences between an inspection versus a service. Below is a list of questions we may ask in order to help get you the right solution.

Bin vents are pulse jet style industrial dust collectors typically used to vent displaced air and harmful products in bins, silos or any other device or process that must contain or control dust particles. Below is a list of questions we may ask in order to help get you the right solution.

If you’re not familiar with how to calculate dust collection CFM, the process can be intimidating. Visit our article here where we will help you understand our approach to calculating CFM requirements for you. Along with the questions you should be asking your dust collection engineering firm to identify the optimal solution for your plant.

Air temperature at the inlet duct is just one of the factors that help our equipment specialist identify the right system for you which will perform safely, efficiently, and reliably for many years. If you would like to learn more about the factors to consider for a new dust collection project, visit our dust collector purchasing guide here.

If you require a fan, check out this resource we have on dust collector fans that will and learn how you can size your dust collector fan with this easy 5-step process. Includes a video and access to a free project consultation with an equipment engineer.

If you’re not familiar with how to calculate dust collection CFM, the process can be intimidating. Visit our article here where we will help you understand our approach to calculating CFM requirements for you. Along with the questions you should be asking your dust collection engineering firm to identify the optimal solution for your plant.

Can velocity is the speed at which air moves from low in the baghouse to high. The higher the can velocity, the faster air moves up in the system. The right can velocity for your dust collection system will be based upon your application and the density of your product. At US Air Filtration our engineers calculate your can velocity based on a few different factors. Visit our can velocity article to get an introduction to dust collection can velocity, it’s importance and impact on system performance, solutions to excessively high can velocity, and how you can calculate yours in 3 easy steps.

Contact us to discuss your requirements of dust seal. Our experienced sales team can help you identify the options that best suit your needs.

Air to cloth ratio in your dust collection system is a critical measurement to keep your system running at peak efficiency. In this article (video option included), learn why it’s crucial to dust collector performance, how to calculate it, and the negative impacts of improper air to cloth ratio.

Air temperature at the inlet duct is just one of the factors that help our equipment specialist identify the right system for you which will perform safely, efficiently, and reliably for many years. If you would like to learn more about the factors to consider for a new dust collection project, visit our dust collector purchasing guide here.

There are multiple strategies for dust collection explosion venting. The best method for your facility will depend on a variety of factors. Learn more about these factors, the best explosion venting strategies, and also prevention methods available in our article here.

“What’s the best way to collect the dust at that dust creation point?” Three common methods are: Tap, Hood, Articulating Arm

Many facilities include source taps at every machine. If there are no taps, then a hood or a smaller pickup point can be added. For example, a hood can be added above a table to capture dust if there is a need to constantly maneuver around the table.

If you require a fan, check out this resource we have on dust collector fans that will and learn how you can size your dust collector fan with this easy 5-step process. Includes a video and access to a free project consultation with an equipment engineer.

The right dust removal method for your dust collector can help you avoid air flow being blocked off, loss of suction throughout the system, and a dangerous explosion that can happen due to dust build-up in the hopper. Learn the factors that go into choosing the right dust removal method and what they are here.

U.S. Air Filtration stocks and supplies control panels for a wide range of dust collection systems. Whether you are looking for a basic no-frills model, or on-demand cleaning capability, PLC integration or a custom-designed panel, we can help you get the right dust collector controls you need. Below is a list of questions we may ask in order to help get you the right solution.

In dust collection, the purpose of a diaphragm valve is to regulate the airflow through the filters to optimize cleaning. Diaphragm valves create a pulse of air which dislodges any dirt and dust on the outside of a filter so that debris can be collected and discarded. Below is a list of questions we may ask in order to help get you the right solution.

Rotary valves are used to transition material from one pressurized point, such as a dust collector, to another unpressurized point, such as a drum or bin. If you would like to learn more about rotary valves, visit our article which includes an overview of the applications they are ideally suited for, rotary valve construction, and the different options available.

Your industrial air pollution control application presents many unique dust collection challenges. Careful planning and attention to your operations processes and dust properties are critical to engineering a reliable baghouse dust collector that will provide optimal plant hygiene, performance and safety for many years to come. Below is a list of questions we may ask in order to help get you the right solution.

If you’re not familiar with how to calculate dust collection CFM, the process can be intimidating. Visit our article here where we will help you understand our approach to calculating CFM requirements for you. Along with the questions you should be asking your dust collection engineering firm to identify the optimal solution for your plant.

The best method of dust removal from your hopper is dependent on multiple components. Learn Is your dust low in density like wood chips or is it higher in density like fine steel dust? Check out this video to learn more about bulk density and other dust properties. more about dust removal options in this article linked here.

Can velocity is the speed at which air moves from low in the baghouse to high. The higher the can velocity, the faster air moves up in the system. The right can velocity for your dust collection system will be based upon your application and the density of your product. At US Air Filtration our engineers calculate your can velocity based on a few different factors. Visit our can velocity article to get an introduction to dust collection can velocity, it’s importance and impact on system performance, solutions to excessively high can velocity, and how you can calculate yours in 3 easy steps.

Air to cloth ratio in your dust collection system is a critical measurement to keep your system running at peak efficiency. In this article (video option included), learn why it’s crucial to dust collector performance, how to calculate it, and the negative impacts of improper air to cloth ratio.

Air temperature at the inlet duct is just one of the factors that help our equipment specialist identify the right system for you which will perform safely, efficiently, and reliably for many years. If you would like to learn more about the factors to consider for a new dust collection project, visit our dust collector purchasing guide here.

There are multiple strategies for dust collection explosion venting. The best method for your facility will depend on a variety of factors. Learn more about these factors, the best explosion venting strategies, and also prevention methods available in our article here.

“What’s the best way to collect the dust at that dust creation point?” Three common methods are: Tap, Hood, Articulating Arm

Many facilities include source taps at every machine. If there are no taps, then a hood or a smaller pickup point can be added. For example, a hood can be added above a table to capture dust if there is a need to constantly maneuver around the table.

If you require a fan, check out this resource we have on dust collector fans that will and learn how you can size your dust collector fan with this easy 5-step process. Includes a video and access to a free project consultation with an equipment engineer.

The right dust removal method for your dust collector can help you avoid air flow being blocked off, loss of suction throughout the system, and a dangerous explosion that can happen due to dust build-up in the hopper. Learn the factors that go into choosing the right dust removal method and what they are here.

Dust collectors vary in height, width and depth depending on the application and the amount of dust being captured. Take note of any height or space restrictions in the work environment and take measurements of the space allotted for your collector along with the space available around the collector. Many dust collectors are top load which means you will need to allow space above the collector to replace and service the collector from the top of the unit. To learn more about identifying the right solution for your application, visit our complete Dust Collector Purchasing Guide here.

Choosing the right filter bags for your dust collection system is critical to ensuring long term, reliable performance of your collector and the safety of your employees. Our How to Select the Right Dust Collector Filter Bags” guide will help you understand your facility’s unique dust properties and also provides an overview of various filter media, construction, and treatment options available

Industrial dust collector filter bags are used in multiple styles of industrial dust collection systems that range from pulse-jet, plenum-pulse, reverse air, and shaker baghouses. Filter bags aid in collecting dust particulate which helps to improve air quality, eliminate potential fire hazards, and keep dust from negatively affecting the product quality. Below is a list of questions we may ask in order to help get you the right solution.

Filter bag configurations can vary from one dust collector to another. Baghouse filter top and bottom configurations will be dependent on the type of baghouse dust collector you have. The most common types of baghouses are pulse-jet and plenum pulse, reverse air, and shaker. Visit our article to learn more about the most common types of industrial baghouses, and the most widely used top and bottom filter bag configurations.

The type of cage you have will depend on the design of your baghouse.Get an overview of baghouse cages, the most common construction options, treatments, how a venturi works with a cage, and more with our Baghouse Cage Construction article here. Below is a list of questions we may ask in order to help get you the right solution.

Industrial fans are used in dust collection systems to push dust-laden air through the filters. Fans can either force a draft (push air) or induce a draft (suck air) through the dust collector. Industrial fans are an essential component to a dust collection system so it’s important to choose the right size fan to make sure you have adequate suction to remove dust from the work environment. Below is a list of questions we may ask in order to help get you the right solution.

Static pressure plays a critical role in the design and performance of pulse jet baghouse dust collection systems. In this article we are discussing the importance of static pressure, what it is, how it’s measured, and how to calculate it.

Air temperature at the inlet duct is just one of the factors that help our equipment specialist identify the right system for you which will perform safely, efficiently, and reliably for many years. If you would like to learn more about the factors to consider for a new dust collection project, visit our Dust Collector Purchasing Guide here.

A well maintained dust collector ensures your system is performing at peak efficiency. It’s also critical to minimizing unscheduled plant downtime and the wear and tear of your dust collector parts. In addition to a preventative maintenance plan, customers can also request a visit from bonded and insured technicians to perform either a dust collector inspection or service. Below is a list of questions we typically ask in order to provide a quote. For more information about dust collector inspection and services, visit this article where we help you understand what’s included and the differences between an inspection versus a service. 

There are three main baghouse styles that are commonly used in most industrial processing and manufacturing applications.  Explore this brief overview of each and their pros and cons.

If applicable, local or federal air permits and guidelines may be required to make sure your plant is meeting air quality standards and local fire codes. These requirements typically come from the Environmental Protection Agency or your local municipality.

Would you like to learn how to install a pleated filter in 8 easy steps? Check out this video, find out how pleated filters can make your bin vent changeouts much easier. If you are looking for a new or replacement pleated bag/filter, below is a list of questions we may ask in order to help get you the right solution.

Rotary valves are used to transition material from one pressurized point, such as a dust collector, to another unpressurized point, such as a drum or bin. If you would like to learn more about rotary valves, visit our article which includes an overview of the applications they are ideally suited for, rotary valve construction, and the different options available. Below is a list of questions we may ask in order to help get you the right solution.

Is your dust low in density like wood chips or is it higher in density like fine steel dust? Check out this video to learn more about bulk density and other dust properties. 

Solenoid and diaphragm valves work together to keep your dust collection system cleaning process perform at peak efficiency. To achieve maximum filter efficiency, you will need to ensure that both are in proper working condition. Below is a list of questions we may ask in order to help get you the right solution.

Timer boards monitor and control your pulse jet dust collector cleaning cycles. The right dust collector timer board option for you can vary depending on your plant’s unique requirements. Timer board options can vary from AC and DC panels, multiple channels, economical no-frills timers, to advanced automated features. We stock and supply a wide selection of brand name timer boards including Dywer, Ametek, Goyen, ACC, and NCC. Below is a list of questions we may ask in order to help get you the right solution.

Are you interested in learning more about Mining Cable Clamp? Contact us today to secure an expert consultation!